9/3/2023 0 Comments Ender 5 hemera![]() SD card 0 detected, interface speed: 20.0MBytes/sec Last software reset at 19:51, reason: User, spinning module GCodes, available RAM 8764 bytes (slot 3) RepRapFirmware for Duet 2 WiFi/Ethernet version 3.0 running on Duet WiFi 1.02 or laterīoard ID: 08DJM-9178L-L4MSN-6J9FD-3S86T-180LP M911 S10 R11 P"M913 X0 Y0 G91 M83 G1 Z3 E-5 F1000" set voltage thresholds and actions to run on power is the response to M122 command G10 P0 R0 S0 set initial tool 0 active and standby temperatures to 0C M950 F1 C"fan1" Q500 create fan 1 on pin fan1 and set its frequency M950 F0 C"fan0" Q500 create fan 0 on pin fan0 and set its frequency M307 H1 B0 S1.00 disable bang-bang mode for heater and set PWM limit M143 H1 S300 set temperature limit for heater 1 to 300C M950 H1 C"e0heat" T1 create nozzle heater output on e0heat and map it to sensor 1 M308 S1 P"e0temp" Y"pt1000" R4700 configure sensor 1 as PT1000 on pin e0temp M307 H0 B0 S1.00 disable bang-bang mode for the bed heater and set PWM limit M143 H0 S120 set temperature limit for heater 0 to 120C M950 H0 C"bedheat" T0 create bed heater output on bedheat and map it to sensor 0 M308 S0 P"bedtemp" Y"thermistor" T100000 B4138 configure sensor 0 as thermistor on pin bedtemp G31 P500 X-45 Y3 Z2.5 set Z probe trigger value, offset and trigger height M558 P9 C"zprobe.in+zprobe.mod" H5 F120 T6000 set Z probe type to bltouch and the dive height + speeds M950 S0 C"exp.heater3" create servo pin 0 for BLTouch ![]() M574 Z1 S2 configure Z-probe endstop for low end on Z M574 Y1 S1 P"ystop" configure active-high endstop for low end on Y via pin ystop M574 X1 S1 P"xstop" configure active-high endstop for low end on X via pin xstop M906 X800 Y800 Z800 E800 I30 set motor currents (mA) and motor idle factor in per cent M350 X16 Y16 Z16 E16 I1 configure microstepping with interpolation M569 P3 S1 physical drive 3 goes forwards M569 P2 S0 physical drive 2 goes backwards M569 P1 S1 physical drive 1 goes forwards M569 P0 S1 physical drive 0 goes forwards M550 P"Daniel's Ender 5 pro" set printer name generated by RepRapFirmware Configuration Tool v2.1.8 on Sat 11:08:21 GMT-0400 (Eastern Daylight Time) Configuration file for Duet WiFi (firmware version 3) I have extended the X axis by displacing the front bar of the printer to recover the space lost by the hemera volume Once we made it right I plant to post this guide corrected for others that like to follow later I am trying to offer as many details as possible. Homing (If the printing head is away from the home position, multiple homing makes the head move around the bed, never to the home place)īed Compensation (Probing goes out of the bed) Thanks to Phaedrux and Mitch for the great discussions posted in the forumĮndstops (When homing the machine crush against the endstops) The upgrade was not simple and I have several configuration questions. The printer used to run silently and without major issues, but the reduced menus and lack of wifi connectivity were enough reasons to upgrade. ![]() This is my detailed guide to upgrade a Ender 5pro with Hemera and Bltouch from Creality silent board 1.15 to Duet 2 Wifi with Firmware 3.0
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |